컨텐츠 바로가기


product


이전 제품 보기

다음 제품 보기

크게보기

[P0000JRD] 16채널 PWM 서보모터 드라이버 모듈 PCA9685 DRIVER MODULE 적립금

() 해외배송 가능

16채널 PWM 서보모터 드라이버 모듈 PCA9685 DRIVER MODULE 기본 정보
판매가
소비자가 0원
적립금
  • 0 (0%)
  • 무통장 결제시 적립금 ( %) 무
  • 카드 결제시 적립금 ( %) 카
  • 실시간 계좌 이체시 적립금 ( %) 실
  • 적립금 결제시 적립금 ( %) 적
  • 휴대폰 결제시 적립금 ( %) 휴
무이자할부
제조사 자체제작
원산지
상품코드 P0000JRD
수량

updown

국내/해외배송
SNS 상품홍보
QR코드  

이미지저장 | 코드URL복사

QR코드 보내기 페이스북으로 보내기 트위터로 보내기 미투데이로 보내기 요즘로 보내기

장바구니 담기 관심상품 등록 추천 메일 보내기

쇼핑 계속하기 바로 구매하기

event

상품상세정보

 

최대출력이 25mA라서 모터를 돌리기에는 출력이 부족할수도 있습니다.

이때에는 서보모터의 전원은 별로도 공급하고 이모듈로 PWM신호를 넣는방법도 가능합니다. (모듈과 서보모터사이 GDN결합 필요)


You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now?

Using only two pins, control 16 free-running PWM outputs! You can even chain up 62 breakouts to control up to 992 PWM outputs

It's an i2c-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!

It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)

6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs

Adjustable frequency PWM up to about 1.6 KHz

12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate

Configurable push-pull or open-drain output

Output enable pin to quickly disable all the outputs

We wrapped up this lovely chip into a breakout board with a couple nice extras

Terminal block for power input (or you can use the 0.1" breakouts on the side)

Reverse polarity protection on the terminal block input

Green power-good LED

3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header

"Chain-able" design

A spot to place a big capacitor on the V+ line (in case you need it)

330 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial

Solder jumpers for the 6 address select pins
 



배송 정보

  • 배송 방법 : 택배
  • 배송 지역 : 전국지역
  • 배송 비용 : 3,000원
  • 배송 기간 : 1일 ~ 2일
  • 배송 안내 :

상품 사용 후기

상품의 사용후기를 적어주세요.

게시물이 없습니다

모두 보기 사용 후기 쓰기

상품 Q&A

상품에 대해 궁금한 점을 해결해 드립니다.

게시물이 없습니다

모두 보기 상품 Q & A 쓰기